DART ZONE PRO MK 2 PRO
DART ZONE PRO MK 2 FREE

It is possible to push even higher with either a spring replacement, or spring spacers but for a secondary pistol I am happy with the fps as is now. The orange muzzle tip clips on and can be tough to remove/install, cutting out the webbing behind the clips make this a lot easier.ДЄdditional minor mods: custom grip plates, safety switch deleteДЄfter all fixes, my MK2 is hitting 130-140fps 'as advertised'. Be careful to clean up any glue that squishes to the Inside of the barrel/breech. Glue is required shims are for mechanical positioning but are not airtight on their own. I then applied silicone rtv adhesive and slid the shims flush with each end. after cutting I slipped 3d printed shims over each end, then 'fluted' the cut ends outwards so darts could insert smoothly. I cut the length to be identical to the original 16mm aluminum barrel. as a bonus this also reduced the Sound of spring ringing/vibration when firing. The ends of the spring are rough, I ground then flat to reduce the tendency for the spring to buckle when compressing, if you can get the spring to balance standing up, the ends are good.ДЄlso, the Plunger Rod has a loose fit with the spring, I 3d printed shims that insert into it to help hold alignment with the spring. Good plunger head alignment is important for the air seal. Be Very Careful if doing this, cuts Must Not go too deep if they reach the O-ring groove you will destroy the breech seal. If the item details above arenвЂ™t accurate or complete, we want to know about it.

DART ZONE PRO MK 2 PRO

Test your speed and accuracy as a Pro Player with the new Dart Zone Pro MK-2 Dart Blaster. To fix this I carved relief vents onto the pusher face. The Pro MK-2 is packed out with 18 half-length Pro Darts that shoot up to 120 feet. Turns out that the pusher would attempt to 'vacuum load' darts. It fits into the groove in front of the ring and pushes it up the sloped section to seal tighter.ДЄfter getting a perfect PT seal, I found unusual resistance when priming forward. So I designed a permanent 3d printed shim. Initially I used teflon tape under the ring, but found that over time it would slip out of position and lose its seal. Unfortunately, due to the oval shape the ring is being stretched and this does not seem to work properly. Most blasters use a 'floating seal' where the O-ring groove has a sloped rear meant to force the ring against the PT walls as it moves forward for a dynamic seal. Thanks to Bradley Phillips for pointing out the source of issues. Hitting from 99-120 fps vs the 130-140s seen in popular review videos. вђпёЏвђпёЏвђпёЏвђпёЏвђпёЏ, would buy again if I needed 2.My DZP MK2 was performing subpar out of the box. You come from outside the hobby, pick this up, and be ready to go. Overall impressions: this is a loadout in a box. All shot but there was a much different sound from the waffles and they didnвЂ™t have the same power. I tried workers, AF pros, included bamboos, and cut down AF waffles on the stream. IMO they shouldвЂ™ve put a larger orange ring on the front instead of this thing.Д¬omes with enough darts to load the blaster and both mags. The orange thing is trash and basically useless.

Complaints are that thereвЂ™s an anti-deprime lock, the safety is mushy (doesnвЂ™t snap on/off can gradually slide along itвЂ™s whole throw distance), and it doesnвЂ™t spin as nicely as my hammershots do. It is short draw so even if it is hard itвЂ™s only hard for a brief movement. I didnвЂ™t notice the prime being bad, but IвЂ™m not a good judge (I donвЂ™t complain about k26 caliburns either рџ¤·вЂЌв™ЂпёЏ). Mk2 itself is an excellent size and feel, slide feels great because itвЂ™s long enough for my whole hand and has nubs that keep your hand from sliding off. Also will need to mark which way the clips are facing on the holder once I settle on a preferred setup. The clip holder holds securely (two-handed violent shaking to drop the clips), and while it HAS a slot to let you reload while holstered, the follower canвЂ™t advance because itвЂ™s blocked by the holster body.

Likely means leaving the clips loaded is вЂњsafeвЂќ, but time will tell. The clip springs are really light and rattle when empty.

DART ZONE PRO MK 2 FREE

Holster has 3 click positions, is a hair loose (I can shake the blaster free shaking it pretty violently), and has a spot that needs trimming to avoid catching the front sight on holstering Text of post if you donвЂ™t have Instagram:

Dart zone pro mk 2